Supply, Charge 
and Protect

VAL-SEC-T2-350-P

Replacement plug for surge arresters from the VALVETRAB SEC product range for L-N and L-PEN paths.

VAL-SEC-T2-3S-350/40-FM

Pluggable surge protective device, in accordance with Type 2/Class II, for 3-phase power supply networks with separate N and PE (5-conductor system: L1, L2, L3, N, PE), with remote indication contact. With 40 kA discharge capacity in accordance with the requirements of VDE 0100-534:2016-10 relating to SPDs at the system feed point.

PT 2XEX(I)-BE

Base element for protective plug PT with protective circuit for two 2-core floating EEx ia signal circuits. Mounting on NS 35/7.5 and NS 35/15, housing width: 17.5 mm

PT 4- 5DC-ST

Protective plug PT with protective circuit for a 4-core floating signal circuit. Nominal voltage: 5 V DC

TTC-6-TVSD-C-24DC-PT-I

Fine surge protection with integrated status indicator for a signal wire with grounded reference potential.

TTC-6P-1X2-F-M-24DC-UT-I

Surge protection, consisting of protective plug and base element, with integrated status indicator and disconnect knife for a 2-wire floating signal circuit, e.g., 0(4) mA ... 20 mA current loop. Indirect grounding via gas discharge tube, HART-compatible. Can be used in safety-related circuits up to SIL 3.

PT 2XEX(I)-24DC-ST

PT protective plug with protective circuit for two 2-wire floating Ex i signal circuits. Nominal voltage: 24 V DC, HART-compatible.

VAL-MS-T1/T2 335/12.5/3+1

PT 1X2+F-BE

Base element for protective plug PT with protective circuit for a 2-core floating signal circuit. Integrated gas arrester as coarse protection between GND and PE. Mounting on NS 35/7.5 und NS 35/15, housing width: 17.5 mm.

VAL-SEC-T2-N/PE-350-P

Replacement plug for surge arresters from the VALVETRAB SEC product range for the N-PE path.

TTC-6-FMRS-PT

Module set for the optical monitoring and floating remote signaling of adjacent surge protective devices in the TERMITRAB complete or CLIXTRAB product family. Suitable for directly grounded DIN rails.

FLT-SEC-T1+T2-1C-350/25-FM

Plug-in lightning and surge arrester combination, in accordance with Type 1+2/Class I+II, for 1-phase power supply networks, with combined PE and N installed in one conductor (L1, PEN).

FLT-ISG-100-EX

Isolating spark gap for the hazardous area with plastic sleeve and M10 connection thread screws. For indirect connection/grounding of operationally isolated system parts in the event of lightning.

BLT-T2-1S-320-UT

Type 2 surge arrester for universal mounting in lights, cable connection boxes, installation boxes, sill-type trunking, underfloor installations or direct installation in the end device. Specifically for insulation class I with optical fault indication. Installation in branch or through wiring. Version: 230 V AC

FLT-SEC-P-T1-1S-350/25-FM

Plug-in lightning current arrester, in accordance with Type 1/Class I, for 1-phase power supply networks with separate N and PE (L1, PE, N).

PT 1X2-BE/FM

Base element to accept a protective plug with diagnostic and status indicator for one floating double wire

FLT-SEC-T1+T2-1S-350/25-FM

Plug-in lightning and surge arrester combination, in accordance with Type 1+2/Class I+II, for 1-phase power supply networks, with separate N and PE (L1, PE, N).

PT 1X2-24DC/FM-ST

Surge protection plug with integrated diagnostic and status indicator on the module and remote indication contact for a 2-wire floating signal circuit.